Thinking about replacing your iPhone’s damaged  screen when your phone is already out of warranty? Well, it may sound very tricky but with our guide, you can do it if you want it to do by yourself. We have previously written about how to replace iPhone 6 screen we will further help you to replace screen in iPhone 6S. As many of you know Techyuga is best iPhone repair center in kolkata and indeed the best place for iPhone 6S Screen Replacement in kolkata for our readers we have this perfect DIY guide today…Let’s check out –

 

If you are facing any kind of issue with your iPhone or apple device then we can help you with that, We are the best place for iPhone Repair in Kolkata. Techyuga has brought city’s best technical experts to your door, Just call us at 9088888835 or Live chat with our support representatives. Or you can directly book a technician here.

 

 

iPhone 6S Screen Replacement In Kolkata

 

Step 1. Pentalobe Screws

 

Power off your iPhone before beginning disassembly.
Remove the two 3.4 mm P2 Pentalobe screws on the bottom edge of the iPhone, next to the Lightning connector.

Pentalobe screws in iPhone 6S

 

Step 2. Opening Procedure

 

removing iPhone 6s display

 

Opening the display on the 6s separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It’s possible to complete the repair without replacing the adhesive, and you probably won’t notice any difference in functionality.
Apply a suction cup to the lower left corner of the display assembly.
Take care not to place the suction cup over the home button.

 

Step 3

 

removing iPhone 6s display

Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices and is held down with adhesive.
Pulling too hard may damage the display assembly. Apply just enough pressure to create a small gap between the display assembly and the rear case.

 

Step 4

detaching display from iPhone 6S

 

There is a notch on the underside of the display, just above the headphone jack. This is the safest place to begin prying the phone open.
Place the flat edge of a spudger into the gap between the screen and rear case, directly above the headphone jack.

 

Step 5

 

Removing iPhone 6s display assembly

Twist the spudger to widen the gap between the front panel assembly and the rest of the phone.

 

Step 6

 

Replacing display in iPhone 6s

 

Insert the flat end of the spudger on the left side of the phone, between the display assembly and rear case.
Slide the spudger up the side of the phone to separate the adhesive and pop the clips free.

 

Step 7

removing iPhone 6S display

 

Remove the spudger and reinsert it on the bottom edge, where you pried the phone open.
Slide the spudger to the right, along the bottom edge of the phone.

 

Step 8

 

Spudger tool in iPhone 6S

 

Slide the spudger up the right side to continue separating the adhesive and popping the display clips free from the iPhone.

Need help about iPhone 6S Screen Replacement ? Get Help from Kolkata’s best iPhone repair center.

 

Step 9

 

Removing iPhone 6S display

 

Use the suction cup to open the display, breaking the last of the adhesive.
Don’t open the display more than 90º, as it is still connected at the top by three cables that may break if stretched.

 

Step 10

 

iPhone 6S display removal

 

Pull up on the nub on the top side of the suction cup to remove it from the front panel.

 

Step 11

 

Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.

 

iPhone 6S display assembly replacement
Open the display to about a 90º angle, and lean it against something to keep it propped up while you’re working on the phone.
Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
In a pinch, you can use an unopened canned beverage to hold the display.

 

Step 12 Battery Connector

 

removing battery connector screws

 

Remove the two Phillips screws securing the battery connector bracket:
One 2.9 mm screw
One 2.2 mm screw

 

Step 13

 

removing battery bracket in iPhone 6S

 

Remove the battery connector bracket from the iPhone.

 

Step 14

 

Disconnecting battery connector iPhone 6S

 

Use the point of a spudger to disconnect the battery connector by prying it straight up from the logic board.

 

Step 15

 

removing battery connector in iPhone 6s

 

Push the battery connector away from the logic board until it stays separated from its socket, so as to avoid any accidental connection to the battery while you work.

 

Step 16 Front Panel Assembly

 

Removing screws in iPhone 6S

 

Remove the following four Phillips screws securing the display cable bracket:
Three 1.2 mm screws
One 2.8 mm screw

 

Step 17

 

Display cable bracket in iPhone 6S

 

Remove the display cable bracket.

 

Step 18

 

iPhone 6S display assembly replacement

 

Use the flat end of a spudger, or a fingernail, to disconnect the front camera flex cable by prying it straight up from its socket on the logic board.

Need help about iPhone 6S Screen Replacement ? Get Help from Kolkata’s best iPhone repair center.

 

Step 19

 

Disconnecting digitizer cable in iPhone 6S

 

Use the flat end of a spudger, or a fingernail, to disconnect the digitizer cable by prying it straight up from its socket on the logic board.
When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.

 

Step 20

 

disconnecting display data cable iPhone 6S

 

Use the flat end of a spudger, or a fingernail, to disconnect the display data cable by prying it straight up from its socket on the logic board.

 

Step 21

 

Removing apart iPhone 6S screen

 

Remove the display assembly.

 

Step 22 Home Button Assembly

 

Removing screws from the bracket iPhone 6S

 

Remove the three 1.7 mm Phillips screws securing the home button bracket.

 

Step 23

 

Removing home button bracket iPhone 6S

 

Lift the lower edge of the home button bracket until it clears the small peg on the right side.
Slide the bracket out from under the EMI shield to remove it.

 

Step 24

 

Disconnecting home button bracket iPhone 6S

Use a spudger to disconnect the home button connector by popping it out of its socket on the back of the display panel.

 

Step 25

Prepare Opener tool and lay it over the lower edge of the front panel to soften the adhesive on the home button gasket.

 

Step 26

 

Removing home button gasket iPhone 6S

 

Flip the front panel over and use a plastic opening pick to carefully separate the home button gasket from the front panel.

 

Step 27

 

removing button gasket front panel iPhone 6S

 

Gently press up on the home button from the front side of the display assembly to continue separating the button gasket from the front panel.

Need help about iPhone 6S Screen Replacement ? Get Help from Kolkata’s best iPhone repair center.

 

Step 28

Prying home button cable iPhone 5S

 

Use the pointed tip of a spudger to pry the home button flex cable off the back of the display panel.

 

Step 29

 

Removing home button assembly iPhone 6S

 

Remove the home button assembly.

 

Step 30 Display Assembly

 

Removing display assembly in iPhone 6S

 

 

Only the front panel remains.

 

 

Call 9088888835 OR Live chat with our engineers here, You can also book a technician below. For more information, check out our iphone repair in kolkata page HERE.

 

 

* You can only book technicians for iPhone repair in Kolkata area. However, if you want us to fix your iPhones you can send us your device via courier service. For more information, please live chat with our support engineers or call 9088888835 now.

 

[ Courtesy : The Blog was originally published in iFixit ]